window repairs near me to uPVC Windows
uPVC windows are an excellent choice for modern homes. They are easy to maintain, durable and long-lasting. They are not susceptible to rot or rust like timber and aluminum.
It is important to clean and oil UPVC doors and windows on a regular basis. This will help prevent costly repairs and improve energy efficiency.
1. Broken Glass
The damaged glass in your windows can cause severe damage to your home and may even be fatal. It is important to ensure that your windows are in good shape.
Single-pane windows are relatively simple to replace and typically fit into old frames very easily. However If you have double-pane windows that are anchored by internal beading, it'll be more difficult to take out the panes that are in place and replace them with new ones. In this situation you'll need to find some plastic spacers that help the new pane to fit correctly into the frame of the window.
Wearing eye protection and heavy gloves is a must if you plan to remove the glass by yourself. It is also recommended to lay down a dropcloth before you begin working on the glass so that any fragments of glass fall on the fabric instead of landing on the floor where they could be trampled on and cause further damage.
Once the glass has been removed and the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to block water and drafts from entering the home until a professional is able to come out and fix the window. It also acts as a barrier, deterring any intruders from getting access to your home. If the gap is particularly large, you may want to consider using an alarm door that comes with an integrated window, since this will offer the best of both worlds.
2. Sagging
Upvc windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber sash windows. Over time, they can develop a variety of issues, including sliding. A sagging window can cause problems with light, draughts or even security. If you find that your uPVC window is beginning to shrink, it's crucial to act fast to prevent the problem from getting worse.
To repair a window that is sagging, you can try to reposition the hinges. To do this, you'll need to open the window so that you can access the frame. Then, remove both the hinges on the top and bottom using a screwdriver, and then adjust them clockwise or counter-clockwise. Once you've adjusted the hinges, close your window and verify the fit. If you are happy with the size of the window, tighten the screws to hold them in the right position.
If you can't reposition the hinges, you may need to replace the seal. As time passes, rubber seals lose their elasticity and become dry which causes them to loosen. If this happens, it's crucial to replace the seal as quickly as possible to ensure your uPVC windows are waterproof and secure from draughts.
UPVC handles can also loosen up. The majority of the time, this is caused by screws that have come loose over time. However, it could also happen because the handle mechanism has worn out. It's a good thing that it's simple to repair the handle of a window that is loose yourself. First, you'll need to shut the window and then perform an initial fitting. The joints at the corners of the sash should align with the joint on the casing. If it doesn't, you can make use of a screwdriver to loosen the handle and turn the mechanism back into its original position.
3. Water Leaks
If you're waking up to wet floors and damp walls each time it rains it is important that you take action. Leaks of water from windows can cause structural damage to your home, and hinder your ability to control the temperature inside your home. The most common reason for leaking uPVC windows is that the sealant around the frame is damaged or missing.
This is an easy fix that can be done by any DIYer who is competent. Depending on the severity of the problem the caulking that was used up might need to be removed before a new layer of caulk is applied. When it is time to uPVC repair, it is important to be careful not to over-caulk. This can make your window more difficult to clean and lower its energy efficiency.
Make sure that the drainage holes have no debris in them, and also that the sill pan has been properly angled to drain away from the window. In more serious cases you might have to consider replacing the window.
Moldy sills and rotten ones are another sign of water leakage. This fungus thrives in humid conditions and can propagate quickly throughout the home.
It is also important to remember that if the leak originates from the glass of your double glazed windows it may be more likely to be an issue with the glass seal rather than the frame or sliding. Again this can easily be corrected by a uPVC window specialist who can replace the glass seal and regain the full insulation properties of your windows.
4. Faulty Hinges
Hinges could be at fault if your uPVC window is difficult to open or it opens with a breeze. They can be replaced by any competent DIYer and are usually completed in just a few minutes.
Most households in the UK will have either top hung or side hung uPVC windows that use hinges and like any mechanical part they can wear down over time. It's very simple to change a window hinge however it is simpler if you have someone to help hold the frame.
It is also important to ensure that the uPVC hinges are opened and closed in the correct direction. This can be done by looking for the arrow on each hinge, this indicates which way the window should open.
Window hinges that aren't working properly can be caused by incorrectly opening the window a certain way or by poor installation at the factory. It is usually possible to fix the issue by sending us a photograph through our website and we will be happy to give you advice.
It is also essential to lubricate the hinges on a regular basis. Applying a light engineering lubricant on the hinges is an ideal method to accomplish this. We suggest using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can make the window easier to open and close. It can also stop corrosion and decrease the chance of sticking. It is recommended to perform this every year. WD40 or other solvent-based oils are not recommended as they could damage your uPVC windows.
5. Draughts
Draughts in upvc windows can be caused by different things. First, the hinges due to wear and tear could become misaligned. This can cause gaps to develop between the sash and the frame. These can be easily repaired by giving them good cleaning, but if they are beyond repair it could be necessary to get them aligned or replaced. The interlock, which is on the hinge side of the window and can be misaligned. Again, it's possible to give them a clean but in some cases it might be necessary to have them replaced.
The next common reason for draughts is window seals. These are susceptible to being worn out or damaged over time and let air escape through the gaps. Replacing these with high-quality weatherstripping can help prevent draughts. Replace the windows made of Upvc with low-emissivity lenses. This will help control indoor temperatures and lessen the possibility of draughts.
Lastly, one of the most effective ways to reduce drafts is to use a draught excluder, these are typically fabric tubes that are filled with some sort of filler and can be positioned on top of your windowsill. They can help block out cold air and keep your home warm and cozy!
With a bit of regular maintenance and repair your windows made of upvc will continue to provide an excellent level of insulation and security for your home. It is crucial to keep in mind that all windows eventually wear out and it may be more cost-effective to replace them rather than repair them. If you encounter any issues with your upvc window, it's best to consult a professional immediately.